Routine check point preparation essentials ? Precision presses ? Inspection and
maintenance products Point inspection essentials Before beginning the primary
motor 1 punch
studio culver city. Parts from the refueling Oil pump to verify [Make
reference to operating instructions and nameplate for oil indication] 2.
Lubricant tank along with other oil towards the oil device Make use of a
dipstick or visually check 3. Lubricant pressure check and oil flow confirmation
Pressure gauge within the normal scale range 4. Air pressure check Pressure
gauge within the normal scale range [Total plant air pressure ought to be above
5kgf / cm2] 5. Clutch. Brake air solenoid valve for dynamic inspection Turn the
operation selector change to JOG, and press the RUN button to listen to the seem
of air exhausted in the solenoid valve 6. Look into the secure, nut class if the
loose 7. Check whether there's leakage, leakage Particularly with the mold with
installing bolts, nuts, with respect to the loose condition to lock or replace 8
punch update. Look into the parts of whether
cracking, damage, deformation, abnormal After the reason for the analysis,
repair or substitute
9. Look into the operation panel, user interface, safety
devices along with other abnormalities Attention ought to be compensated to
wiring off, damaged, abnormal relay crunch and so forth Following the primary
motor starts 1. Flywheel running condition and running direction check Special
attention ought to be compensated towards the start condition, acceleration
condition, vibration and seem. Once the idling has ended 2 minutes and also the
rotation resistance is big, the V belt vibration 2. The indicator worth of the
instrument check Once the pressure gauge, galvanometer bad, to regulate or
replace 3. Clutch, brake the experience point inspection close. Open the great,
abnormal seem, vibration, etc. have to be adjusted within the Jog operation, and
so the safety of a vacation to investigate second amount of protection device is
a great function 4. Emergency stop Action check The crank position is 90 ¡ã. ,
Press the emergency stop button to see the slide position Whether it's too big,
and find out the causes of the publish-readjustment 5. Die high check Within the
jog operation, the analysis. The mutual position from the lower mold 6. Mold,
installing of good or otherwise the check Analysis of locking, the position of
the lower and upper mold and mold damage [Particularly, mold installation, the
necessity to concentrate on steer clear of the eccentric load] Check during
operation 1. Clutch. Brake frequent lowering and raising bad, charred along with
other anomalies Focus on if the seem, coke smell, smoke and air leakage and so
forth 2. Check the quality of brake slippage Note Slide stop position, position
is simply too large (crank position ¡À 10. Above] ought to be adjusted
immediately 3. Look into the scale change of every calculating instrument 4.
Check every part from the oil spills, gas and so forth Pressure is not high
enough, the present meter changes punch
using white grape juice, for example counting action
5. Slide the guide
surface, for example abnormal point inspection Focus on if the fever, burning
and scratches 6. Each shaft is exposed to some heat check like a part 50 ¡ã C or
fewer 7. Motor fever check The periphery of 60 ¡æ below 8. Mold pad pressure
check [when utilizing mold pad] 9. Overall visual inspection Seek advice from
the size from the pressure gauge and also the capacity value shown on the
nameplate Look into the work following the preparation 1. Operation using the
key switch from the closed 2. Close the environment line pump The bottom line is
held by the pack leader accountable for the operation ? 3. The environment pipe
from the drainage pipe In the drain valve discharge or hvac filters along with
other drains drain 4. Every part from the clean, point inspection 5. Punching
equipment in general check 6. Refuel the required parts 7. Upkeep of tools 8.
Switch off the ability ? Cracking, injuries, loose and so forth
没有评论:
发表评论